All Products

Gear set, differential (output gears (2)/ spider gears (2)/ spider gear shaft, carrier support)

Engine mount (complete assembly)/ 3x28mm CS with washers (2)/ 3x10 CS with washers (10), ELW 3x6.5x.45 (3)

Springs, shock (natural finish) (GTX) (1.538 rate, red stripe) (2)

SixtyFour & FiftyNine Light KitDesigned specifically for the SixtyFour & FiftyNine. The light kit has been programmed to work correctly out...

Elevate your precision with the MIP 4.0mm Speed Tip Hex Driver Wrench Gen 2. This high-performance tool, designed for demanding tasks, seamlessly i...

Diff Drive Ring 2.60:1 GT/B4/T4

X-Series Sensor Harness

Wheel washers, blue (4)

Bulkhead, rear (upper and lower)

KAOS Two way Adjustable Tow Hitch, for CEN Racing F250 or F450

High quality machined brass shaft collars that are great for wire landing gear and axle shafts. Enough stock so that threads will not strip and ca...

Suspension pins, 4x85mm (hardened steel) (2)

Suspension pin retainer (4)

Spur gear, 83-tooth (48-pitch) (for models with Torque-Control slipper clutch)

Camber link set for Bandit® (gray) (plastic/ non-adjustable)

Carriers, Stub Axle, Rear, Extreme Heavy Duty, Green (Left and Right)/ 3x41mm Hinge Pins (2)/ 3x20mm BCS (2) (for Use with #9080 Upgrade Kit)

Covers, gear (2)

Driveshaft assembly, rear, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Steering Blocks, Extreme Heavy Duty, Red (Left and Right)/ 3x20mm BCS (2) (for Use with #9080 Upgrade Kit)

Differential, rear (complete with pinion gear and differential plastics) (fits 1/10-scale Rally & 4X4 VXL models: Slash®, Stampede®, Rustler®) ...

Ball bearings, blue rubber sealed (5x11x4mm) (2)

Includes:1 Pinion2 Grub ScrewsFeatures:8mm BoreM5 Grub ScrewsStrong and durable Hardened Steel for long-lasting performanceTwo set-screw holes for ...

Charger, iD® Balance, USB (2-cell 7.4 volt LiPo with iD® connector only)

Hardware Kit, Sledge® (contains All Hardware Used on Sledge®)

Stub axle, aluminum, (blue-anodized) (1) (for use only with #7750X or 7896 driveshaft)

Driveshaft assembly, rear, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Suspension pins, 2.5x31.5mm (king pins) with E-clips (2) (strengthens caster blocks)

Driveshaft assembly (1), left or right (fully assembled, ready to install)/ M3/12.5mm yoke pin (1)

Driveshaft assembly, front, extreme heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Limit strap, rear suspension (2)/ 3x8 flat-head screw (4)

Suspension arms, rear (left & right)

Gear cover (rear chassis brace)/ wire retainer

Gear set, differential (output gears (2)/ spider gears (2)/ spider gear shaft/ diff carrier support)

Spur Gear, 50-tooth (machined, Hardened Steel) (wide Face, 1.0 metric Pitch)

Trailing arm (2) (assembled with hollow balls)

Suspension arm set, front (includes upper right & left and lower right & left arms)

Springs, rear (progressive, +20% rate, blue) (2)

Spring retainers, upper & lower (2)/ spring pre-load spacers: 1mm (4)/ 1.5mm (2)/ 2mm (2)/ 4mm (2)/ 8mm (2) (Big Bore Shocks)

Suspension arm set, front (includes upper right & left and lower right & left arms)