Hardware

Gear, 13-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 12-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 14-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Hold down, battery/ hold down retainer/ battery post/ foam spacer/ angled body clip

Driveshaft assembly (1), left or right (fully assembled, ready to install)/ M3/12.5mm yoke pin (1)

Gear, 20-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Clutch bell (15-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip (requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

Suspension pin set, complete (hardened steel, front & rear), 3x27mm (4), 3x35mm (2), 3x52mm (4)

Nuts, 2.5mm nylon locking (12)

Wrist pin (1), Wrist Pin Clips(2) (TRX® 3.3)

Engine mount (complete assembly)/ 3x28mm CS with washers (2)/ 3x10 CS with washers (10), ELW 3x6.5x.45 (3)

Linkage set, throttle & brake, Revo®/Slayer (includes servo horns, rod guides, brake spring, brake adjustment dial, brake lever, rods (wires), ...

Engine mount/ engine mount spacers (2)/ 3x15 CS with washers (4)/ 4x18 BCS (2)/ flat-head engine mount screws 3x10 (2)

Screws, 1.6x5mm button-head, self-tapping (hex drive) (6)

Gear, 11-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Nuts, 4mm flanged (10)

Body clip retainer, green (4)

Center bearing carrier/ bushings (2)

Body clip retainer, black (4)

Body clip retainer, blue (4)

Mounts, suspension pin (rear anti-squat blocks) (1.5, 2.25, 3.0 & 3.75 degree) (1 each)

Rotor head, lower (1)/ screws (2)

Stub axle, CV style (machined steel) (1)/ cross pin (1)/ drive pin (1)

Gear, 18-T pinion (0.8 metric pitch, compatible with 32-pitch) (hardened steel) (fits 5mm shaft)/ set screw

Backplate/ 20x1.4mm O-ring (for engines w/o starter) (TRX® 2.5, 2.5R, 3.3)

Piston/sleeve (matched set), wrist pin clips(2) (TRX® 2.5, 2.5R)

Spacers, steel (Jato® Twin-Spoke wheels, front) (4)

Idler gear, steel (16-tooth)/ idler gear shaft/ 3x8mm flat metal washer/ 8x12x0.5mm PTFE-coated washer/ 3x6mm flat metal washer/ 3mm nylon locknut ...

Pulleys, 20-groove (middle) (2)/flanges (2)/ axle pins (2)

Driveshaft, steel constant-velocity, Revo®/E-Revo® (first generation)/T-Maxx®/E-Maxx (shaft only, 128.5mm)/ drive cup pin (1)

Linkage, shift, Revo® (includes: ball collar, spring, ball cup, servo horn, linkage wire)

Flywheel Nut 1/4-28 thread (for big blocks w/SG shafts)/

Rocker arm set, progressive-2 (90-T)/ spacers (red aluminum) (8)

Gear set, 2-speed close ratio (2nd speed gear 40T, 13T-16T input gears, hardware)

Wheel nuts, splined, 17mm (blue-anodized) (4)

Driveshaft, steel constant-velocity (shaft only, 58mm)/ drive cup pin (1) (fits front center shaft on T-Maxx®)

Linkage set, rear brake (Revo®) (Includes: brake lever/ rod (wire)/ brake spring/ brake adjustment dial/ rod guide bushing/ 2.5x5x0.75 MW)

Suspension arm set, adjustable wheelbase (lengthens wheelbase 10mm or 19mm) (suspension arm upper (2)/ suspension arm lower (2)/ bumper mount space...

Yoke, brake (1)/ torque pins (2)/ 4x15mm screw pin

Wheel nuts, splined, 17mm (green-anodized) (4)

Yokes, differential and transmission (2)/ 4x15mm screw pins (2)

Spring, header (for Revo® big block header)/o-ring (1) & gasket (1) (for exhaust header flange)

Washer, 7x10x1.0 (2), 7x10x0.5 (1) black steel (shims for flywheel spacing), Washer, 5x8x2.8 brass (1) (shim for clutch bell spacing) for Revo® Big...

Screw, idle speed/ 2x1mm O-ring (1-each) (TRX® 2.5, 2.5R, 3.3)

Throttle arm, carburetor/ 3mm set screw (1-each) (TRX® 2.5, 2.5R, 3.3)