Hardware

Stub axles, front, heavy duty (2)/ yokes (2)/ pins (4)

Driveshaft assembly, front, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Gear, 24-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 18-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 22-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 17-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 15-T pinion (machined) (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 15-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 13-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 12-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 14-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Hold down, battery/ hold down retainer/ battery post/ foam spacer/ angled body clip

Body accessories kit, 2017 Ford Raptor® (includes grille, hood insert, side mirrors, & mounting hardware)

Driveshaft assembly (1), left or right (fully assembled, ready to install)/ M3/12.5mm yoke pin (1)

Gear, 20-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Clutch bell (15-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip (requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

Suspension pin set, complete (hardened steel, front & rear), 3x27mm (4), 3x35mm (2), 3x52mm (4)

Nuts, 2.5mm nylon locking (12)

Wrist pin (1), Wrist Pin Clips(2) (TRX® 3.3)

Big block conversion kit (engine mount and required hardware, Forward Conversion Kit for Transmission)

Gear, 29-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw

Gear, 26-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw

Gear, 13-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Engine mount/ engine mount spacers (2)/ 3x15 CS with washers (4)/ 4x18 BCS (2)/ flat-head engine mount screws 3x10 (2)

Screws, 1.6x5mm button-head, self-tapping (hex drive) (6)

Gear, 11-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Nuts, 4mm flanged (10)

Body clip retainer, green (4)

Center bearing carrier/ bushings (2)

Body clip retainer, black (4)

Body clip retainer, blue (4)

Mounts, suspension pin (rear anti-squat blocks) (1.5, 2.25, 3.0 & 3.75 degree) (1 each)

Rotor head, lower (1)/ screws (2)

Stub axle, CV style (machined steel) (1)/ cross pin (1)/ drive pin (1)

Gear, 18-T pinion (0.8 metric pitch, compatible with 32-pitch) (hardened steel) (fits 5mm shaft)/ set screw

Backplate/ 20x1.4mm O-ring (for engines w/o starter) (TRX® 2.5, 2.5R, 3.3)

Piston/sleeve (matched set), wrist pin clips(2) (TRX® 2.5, 2.5R)

Spacers, steel (Jato® Twin-Spoke wheels, front) (4)

Idler gear, steel (16-tooth)/ idler gear shaft/ 3x8mm flat metal washer/ 8x12x0.5mm PTFE-coated washer/ 3x6mm flat metal washer/ 3mm nylon locknut ...

Pulleys, 20-groove (middle) (2)/flanges (2)/ axle pins (2)

Driveshaft, steel constant-velocity, Revo®/E-Revo® (first generation)/T-Maxx®/E-Maxx (shaft only, 128.5mm)/ drive cup pin (1)

Linkage, shift, Revo® (includes: ball collar, spring, ball cup, servo horn, linkage wire)

Flywheel Nut 1/4-28 thread (for big blocks w/SG shafts)/

Rocker arm set, progressive-2 (90-T)/ spacers (red aluminum) (8)

Gear set, 2-speed close ratio (2nd speed gear 40T, 13T-16T input gears, hardware)

Wheel nuts, splined, 17mm (blue-anodized) (4)