Hardware

Engine mount (complete assembly)/ 3x28mm CS with washers (2)/ 3x10 CS with washers (10), ELW 3x6.5x.45 (3)

Linkage set, throttle & brake, Revo®/Slayer (includes servo horns, rod guides, brake spring, brake adjustment dial, brake lever, rods (wires), ...

Suspension screw pin set, hardened steel (hex drive)

Shoulder screws, steering bellcranks (3x30mm cap-head machine) (2)/ draglink shoulder screws (chrome) (2)

Flywheel nut (TRX® 2.5, 2.5R, 3.3)

Differential output yokes, black (2)/ 3x5mm countersunk screws (2)/ screw pin (2)

Screw pin, 4x15mm (6)

Transmission output yokes (heavy duty) (2)/ set screw yoke pins, M4/10 (1) & M4/18.5 (1)

Clutch bell (14-tooth)/ 5x8x0.5mm fiber washer (2)/ 5mm e-clip (2) (requires 5x10x4mm ball bearings part #4609) (1.0 metric pitch)

Clutch bell (17-tooth)/ 5x8x0.5mm fiber washer (2)/ 5mm e-clip (2) (requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

Screws, 3x8mm flat-head machine (hex drive) (6)

E-clips/ C-rings

Screws, 4x10mm button-head machine (hex drive) (6)

Gear, pinion (28-tooth) (48-pitch) (fits 3mm shaft)/ set screw

Piston/sleeve (matched set), wrist pin clips(2) (TRX® 2.5, 2.5R)

Spacers, steel (Jato® Twin-Spoke wheels, front) (4)

Idler gear, steel (16-tooth)/ idler gear shaft/ 3x8mm flat metal washer/ 8x12x0.5mm PTFE-coated washer/ 3x6mm flat metal washer/ 3mm nylon locknut ...

Pulleys, 20-groove (middle) (2)/flanges (2)/ axle pins (2)

Driveshaft, steel constant-velocity, Revo®/E-Revo® (first generation)/T-Maxx®/E-Maxx (shaft only, 128.5mm)/ drive cup pin (1)

Linkage, shift, Revo® (includes: ball collar, spring, ball cup, servo horn, linkage wire)

Flywheel Nut 1/4-28 thread (for big blocks w/SG shafts)/

Rocker arm set, progressive-2 (90-T)/ spacers (red aluminum) (8)

Gear set, 2-speed close ratio (2nd speed gear 40T, 13T-16T input gears, hardware)

Wheel nuts, splined, 17mm (blue-anodized) (4)

Driveshaft, steel constant-velocity (shaft only, 58mm)/ drive cup pin (1) (fits front center shaft on T-Maxx®)

Linkage set, rear brake (Revo®) (Includes: brake lever/ rod (wire)/ brake spring/ brake adjustment dial/ rod guide bushing/ 2.5x5x0.75 MW)

Suspension arm set, adjustable wheelbase (lengthens wheelbase 10mm or 19mm) (suspension arm upper (2)/ suspension arm lower (2)/ bumper mount space...

Yoke, brake (1)/ torque pins (2)/ 4x15mm screw pin

Wheel nuts, splined, 17mm (green-anodized) (4)

Yokes, differential and transmission (2)/ 4x15mm screw pins (2)

Spring, header (for Revo® big block header)/o-ring (1) & gasket (1) (for exhaust header flange)

Washer, 7x10x1.0 (2), 7x10x0.5 (1) black steel (shims for flywheel spacing), Washer, 5x8x2.8 brass (1) (shim for clutch bell spacing) for Revo® Big...

Screw, idle speed/ 2x1mm O-ring (1-each) (TRX® 2.5, 2.5R, 3.3)

Throttle arm, carburetor/ 3mm set screw (1-each) (TRX® 2.5, 2.5R, 3.3)

Spacer, pushrod (aluminum, red) (use with 5318 or 5318X pushrod and 5358 progressive 2 rockers) (8)

Needle assembly, high-speed (with fuel fitting)/ 2.5x1.15mm O-ring (2)/ 5.3x7.8x.6mm crush washer (2) (TRX® 2.5, 2.5R, 3.3)

Bellcrank bushings (plastic) (4x7x2.5mm) (4)

Gear, 26-T pinion (48-pitch) (fits 3mm shaft)/ set screw

Chassis, 7075-T6 billet machined aluminum (4mm) (blue)/ hardware

Drive hub assembly, clutch/ 6x8.5x0.5mm PTFE-coated washer (1)

Ring gear, 37-T/ 13-T pinion/ diff carrier/6x10x0.5mm PTFE-coated washer (1)/ 2x8mm countersunk machine screws (4)