(623) 251-1080
(623) 251-1080
Driveshaft assembly, front, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)
This is a TLR Steering Hardware Set that includes screws, ball bearings, spacers, and steering posts.
Screws, 3x10mm button-head machine (hex drive) (6)
Screws, 3x12mm countersunk machine (6) (hex drive)
Screws, 4x12mm countersunk machine (hex drive) (6)
These 17mm Aluminum Wheel Nuts provide a strong and reliable fixing for your vehicle's wheels.FeaturesManufactured from lightweight aluminum for re...
View full detailsLimit strap, rear suspension (2)/ 3x8 flat-head screw (4)
Wheel washers (4) Set of four black wheel washers Accessory part for these models: Maxx® Maxx®: TQi Traxxas Link Enabled 2.4GHz Radio & TSM ...
View full detailsWheel nuts, splined, 17mm, serrated (green-anodized) (4)
Carburetor body/ fuel inlet plug/ 5x.9mm O-ring (1-each) (TRX® 2.5, 2.5R, 3.3)
Spring pre-load spacers: 1mm (4)/ 2mm (2)/ 4mm (2)/ 8mm (2)
Screws, 2.5x10mm cap-head machine (hex drive) (6)
Yokes, transmission (2)/ 4x15mm screw pins (2)
Input shaft (slipper shaft) / spring pin
Stub axle pins (4)
Wheel washers, blue (4)
Screws, 3x8mm button-head machine (hex drive) (6)
Gear, 12-T pinion (32-p), heavy duty (machined, hardened steel) (fits 3mm shaft)/ set screw
Driveshaft assembly, rear, extreme heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)
Aluminum spacers: 3x6x1.5mm (2)/ 3x6x2.5mm (1)/ 3x6x3.8mm (2)
Screws, 3x40mm button-head machine (hex drive) (6)
Hold down, battery/ hold down retainer/ battery post/ foam spacer/ angled body clip (allows for installation of taller, multi-cell batteries)
Gear, 14-T pinion / set screw
Screws, 3x30mm cap-head machine (hex drive) (6)
Screws, 3x20mm cap-head machine (hex drive) (6)
Rod ends (16 long & 4 short)/ hollow ball connectors (18)/ ball screws (2)
Wheel nuts, splined, 17mm, serrated (red-anodized) (4)
Nuts, aluminum, flanged, serrated (4mm) (blue-anodized) (4)
Steering bellcranks, drag link (blue-anodized 6061-T6 aluminum)/ 5x8mm ball bearings (4)/ hardware (assembled)
Spring retainer (adjuster), red-anodized aluminum, GTX shocks (4) (assembled with o-ring)
Body accessories, Chevrolet C10, chrome (includes grille (upper & lower), headlight housings (left & right), bumpers (front & rear), mo...
View full detailsWheel nut washer, machined aluminum, blue / 3x12mm CS (4)
Screw set, complete
Stub axle nut, aluminum (blue-anodized) (4)
Gear set, transmission, metal (includes 18T, 30T input gears, 36T output gear, 2x9.8 pins (5))
Yokes, stub axle (2)/ pins (2)
Traction boards, yellow/ mounting hardware
Slide carb linkage set (throttle link, brake link, and hardware)
Adapter nut, clutch/ 3x10mm cap screw/washer/ split washer (not for use with IPS crankshafts)
{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}