(623) 251-1080
(623) 251-1080
Primary clutch assembly/ 2x9.8mm pin/ 6x8x0.5 TW (1)
Aluminum Ball Stud Washer Set, Blue, (12pcs)
These high-quality O-rings provide direct replacement parts for your ARRMA vehicle. Includes 8 x Silicone O-Ring 5.8 x 2.2mm Features Durable pr...
View full detailsLosi - LOS252113The Dogbone - Rear 5mm Pin(2): DBXL-E 2.0 by Losi is a quality built accessory.Product SpecificationsPart Type: Chassis Parts
Driver Type: 2mm HexThread Type: MachineLength: 17.5mmWidth: 3mmHeight: 3mmWeight: 0.01oz
Driver Type: 2mm hexThread Type: MachineLength: 12mmWidth: 3mmHeight: 12mmWeight: 0.01oz
Team Losi Racing - TLR5908The Button Head Screws, M3 x 44mm (4) by Team Losi Racing is a quality built accessory.Product SpecificationsPart Type:...
View full detailsARRMA - ARA310929The Aluminum Wheel Nut 24mm, Red (4) by ARRMA is a quality built accessory.Product SpecificationsPart Type: Chassis Parts
Stub axle nut, aluminum (gray-anodized) (4)
Stub axle nut, aluminum (green-anodized) (4)
Nuts, 5mm flanged nylon locking (aluminum, blue-anodized, serrated) (4)
Traction boards, blue/ mounting hardware
Mirrors, side, black (left & right)/ mirror retainers (2)/ body clips (4)/ o-rings (4)/ spoiler, black/ spoiler retainer (1)/ 1.6x5 BCS (self-t...
View full detailsShock caps, aluminum (blue-anodized), GTX shocks (4)/ spacers (8)
Wheel nut washer, machined aluminum, red / 3x12mm CS (4)
Housing, center differential (aluminum)/ x-ring gaskets (2)/ ring gear gasket (1)/ bushings (4)/ 5x10x0.5 PTW (1)/ 2.5x10 CCS (with threadlock) (4)
Gear set, transmission (includes 18T, 25T input gears, 13T idler gear (steel), 35T output gear, M3x13.75 screw pin)
Input shaft (cush drive)/ pin
Primary gear set (23T and 33T)/ 2x11.8mm pin/ pin retainer/ disc spring
Landing skid set (black-anodized)/ screws (4) (assembled)
Gear, 34-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw
Retainer clip, battery (1)/ front clip (1) /rear clip (1)/ foam spacer (1) (for one battery compartment)
Suspension down stop screws (includes 2.5mm drill bit) (limits suspension droop, sets maximum ride height)
Cross pin (4)/ drive pin (4)/ set screw (4) (to rebuild 2 driveshafts)
Gear set, 2-speed wide ratio (2nd speed gear 38T, 13T-18T input gears, hardware)
Antenna crimp nut, aluminum (red-anodized)/ antenna nut tools
Ultra Shocks (grey) (long) (complete with spring pre-load spacers & springs) (2)
Differential output yokes (2)/ 3x5mm countersunk screws (2)/ 3mm set (set) screws (4)
O-ring set: for carb base/ air filter adapter/high-speed needle (2)/ low-speed spray bar (2)
G-spring retainers (wrist pin keepers) (3)
Screws, 3x8mm washerhead self-tapping (6)
These are 4-40 x .200″ Threaded ball studs with the ball centered 0.169″ above the base.
{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}