Parts

Gear, 23-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Plate, motor, 6061-T6 aluminum (red-anodized) (4mm thick)/ 3x10mm CS with split and flat washer (2)

Gear set, center differential (output gears (2)/ spider gears (2)/ spider gear shaft)

Suspension arms, lower, black (left and right, front or rear) (2) (for use with #8995 WideMaxx® suspension kit)

Springs, shock (natural finish) (GT-Maxx®) (1.210 rate) (2)

Bumper, rear/ bumper mount, rear

Bulkhead, front

Differential output yoke assembly, extreme heavy duty (2) (left or right, front or rear) (assembled with external-splined half shaft)/ screw pin (2)

Chassis (162mm Long Battery Compartment) (fits Flat Style Battery Packs) (use Only with #7430R Front Bulkhead and #6726X Battery Hold-Down)

Wheelie bar, black chrome (assembled)/ wheelie bar mount

Housing, differential (rear)

Half shafts, short (heavy duty) (external-splined (2) & internal-splined (2))/ metal U-joints (4)

Bumper, front/ skidplate, front (black)

Ring gear, differential/ pinion gear, differential (12/47 ratio) (front)

Spur gear, 83-tooth (48-pitch) (for models with Torque-Control slipper clutch)

Air filter and pre-filter inserts, foam (high-volume) (3) (pre-oiled, assembled) (use with #5266 filter body) (TRX® 2.5, 2.5R, 3.3)

Drag link, machined 6061-T6 aluminum (orange-anodized)

Box, receiver (sealed)/ foam pad/ silicone grease/2.5x8mm BCS (2)/ 3x10mm CCS (2)/ 3x15mm CCS (2)

Springs, front (blue) (2)

Axles (front) (2)

Battery door, transmitter (replacement for #6516, 6517, 6528, 6529, 6530 transmitters)

Bumper, rear/ bumper mount, rear (pink)

Coupler, exhaust (siliconee)

Gear, 31-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Turnbuckle, aluminum (red-anodized), camber link, front, 39mm (1) (assembled w/rod ends)/ hollow balls (2) (See part 3741X for complete camber link...

Lower chassis, low CG (blue)

Stub axle carriers (2)

Turnbuckles, toe link, 55mm (75mm center to center) (2) (assembled with rod ends and hollow balls)

Differential output yokes (heavy duty) (2)/ set screw yoke pins, M4/10 (2)

Skidplate, chassis

Turnbuckles, camber links, 58mm (assembled with rod ends and hollow balls) (2)

Suspension arms, front (right), heavy duty (upper (1)/ lower (1))

Suspension arms upper (1)/ suspension arm lower (1) (right front)

Bulkhead, front

Suspension arms, long (rear)

Rebuild kit, steel constant velocity driveshaft (includes drive pin & cross pin for two driveshaft assemblies)

Rebuild kit, TRX-4® shocks (x-rings, o-rings, pistons, bushings, e clips, rod ends, and travel limiters)

Receiver Box Cover (for Use Only with #8224 Receiver Box and #2260 BEC)/ Foam Pads/ Seals/ Silicone Grease

Springs, shock, long (natural finish) (GTS) (0.54 rate, green stripe) (for use with TRX-4® Long Arm Lift Kit)

Suspension arms, rear (left & right)

Suspension pins, 44mm (2) with E-clips

Suspension arms, blue, upper (left or right, front or rear), heavy duty (2)

Push rod (molded composite) (red) (4)/ hollow balls (8)