Parts

Stub axles, rear, heavy duty (2)/pins (2)

Stub axle assembly, front, outer, extreme heavy duty (1) (left or right) (assembled with internal-splined half shaft)

Half shaft, internal splined (steel-spline constant-velocity) (1)

Half shaft, external splined (steel-spline constant-velocity) (1)

Stub axles, front, heavy duty (2)/ yokes (2)/ pins (4)

Driveshaft, center, 6061-T6 aluminum (red-anodized)

Stub axle assembly, rear, outer, extreme heavy duty (1) (left or right) (assembled with internal-splined half shaft)

Half shafts, heavy duty (external splined (2)/ internal splined (2))/ metal u-joints (4)

Cover, gear/ motor wire hold-down clip

Driveshaft, center, 6061-T6 aluminum (red-anodized)

Driveshaft, center, 6061-T6 aluminum (green-anodized) (189mm)

Gear clutch, complete (high stall)

Driveshaft, center, 6061-T6 aluminum (blue-anodized)

Driveshaft, center, 6061-T6 aluminum (red-anodized) (189mm)

Driveshaft, center, 6061-T6 aluminum (orange-anodized) (189mm)

Driveshaft, center, 6061-T6 aluminum (blue-anodized) (189mm)

Driveshaft assembly, front, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Gear set, differential (spider gears (4)/ spider gear shaft (2))

Spur gear, 54-tooth, steel (1.0 metric pitch)

Hub retainer, 17mm hubs, M4 X 0.7 (4) (use with #5853X, #6856X, #6469)

Propeller, 42x59mm

Telemetry trigger magnet holder, center differential/ magnet, 5x2mm (1)/ 3x8mm BCS (3) (for use with #6814 center differential)

Carrier, differential/ x-ring gaskets (2)/ ring gear gasket/ 6x10x0.5 TW

Propeller shaft/ flex cable

Differential output yokes, black (2)/ 3x5mm countersunk screws (2)/ screw pin (2)

Linkage, front sway bar (Revo®/Slayer) (3x70mm turnbuckle) (2) (assembled with rod ends, hollow balls and ball stud)

Clutch bell (15-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip (requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

Pressure plate, slipper (1)

Clutch bell (17-tooth)/ 5x8x0.5mm fiber washer (2)/ 5mm e-clip (2) (requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

Propeller

Transmission output yokes (heavy duty) (2)/ set screw yoke pins, M4/10 (1) & M4/18.5 (1)

Differential output yokes, hardened steel (w/ U-joints) (2)

Carrier, differential (heavy duty)/ x-ring gaskets (2)/ ring gear gasket/ bushings (2)/ 6x10x0.5 TW

Half shafts, long (heavy duty) (external-splined (2) & internal-splined (2))/ metal U-joints (4)

Wheel hubs, 12mm hex (2)/ stub axle pins (2)

Nuts, 5mm flanged nylon locking (aluminum, blue-anodized) (4)

Stub axles, rear (2)

Shafts, idler gear (lightweight 7075-T6 aluminum hard-anodized/ PTFE-coated)

Bulkhead (front) (gray)

Half-shaft pro-pack (internal-splined (6)/external-splined (6)) (plastic shafts only)

Half shaft pro-pack (internal-splined (6)/ external-splined (6) (plastic shafts only)

Half shafts, long truck (external-splined (2) & internal-splined (2)/ metal U-joints (4)

New style plastic propeller for Villain EX. Requires change to smaller pinion gears when used on older Villains equipped with part 1534 and 1533 pr...