Traxxas

Screws, 4x22mm button-head machine (hex drive) (6)

Air filter body (high volume)/ filter support/ cap/ foam filter, pre-filter/ air filter base/ wire mount/ hardware (1 each)

Driveshaft assembly, rear, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Rod ends (4) (assembled with steel pivot balls) (replacement ends for #7748G, 7748R, 7748X, 8542A, 8542R, 8542T, 8542X)

Hardware Kit, E-Revo® VXL (contains All Hardware Used on E-Revo® VXL)

Hardware Kit, X-Maxx® (contains All Hardware Used on X-Maxx®)

Hardware Kit, Maxx® (contains All Hardware Used on Maxx®)

Hardware Kit, Stainless Steel, E-Revo® VXL (contains All Stainless Steel Hardware Used on E-Revo® VXL)

Hardware Kit, XRT® (contains All Hardware Used on XRT®)

Hardware Kit, Sledge® (contains All Hardware Used on Sledge®)

Hardware Kit, Stainless Steel, X-Maxx® (contains All Stainless Steel Hardware Used on X-Maxx®)

Primary clutch assembly/ 2x9.8mm pin/ 6x8x0.5 TW (1)

Gear set, differential, metal (output gears (2)/ spider gears (4)/ ring gear, 35T (1)/ 2x14.8mm pin (1))

Servo horn, steering/ linkage, steering (46mm, assembled with pivot balls)

Spider gear shaft (2)/ spacers (4)/ 16x23.5x.5mm TW (2)

Adapter nut, clutch (not for use with IPS crankshafts)

Collars, screw (2)/ grub screws, 3mm (2)

Nuts, 3mm nylon locking, black (8)

Wheel Nuts, Splined, 17mm, Serrated (gray-Anodized) (4)

Bushings, driveshaft, front (1), rear (1)

Screws, 3x15mm button-head machine (hex drive) (6)

Hardware Kit, Stainless Steel, Slash® VXL/Bandit® VXL/Stampede® VXL/Rustler® VXL (contains All Stainless Steel Hardware Used on Slash® VXL, Bandit®...

Hardware Kit, TRX-4® (contains All Hardware Used on TRX-4®)

Nuts, 5mm flanged nylon locking (aluminum, blue-anodized, serrated) (4)

Traction boards, blue/ mounting hardware

Mirrors, side, black (left & right)/ mirror retainers (2)/ body clips (4)/ o-rings (4)/ spoiler, black/ spoiler retainer (1)/ 1.6x5 BCS (self-t...

Wheel nut washer, machined aluminum, red / 3x12mm CS (4)

Gear set, transmission (includes 18T, 25T input gears, 13T idler gear (steel), 35T output gear, M3x13.75 screw pin)

Input shaft (cush drive)/ pin

Primary gear set (23T and 33T)/ 2x11.8mm pin/ pin retainer/ disc spring

Landing skid set (black-anodized)/ screws (4) (assembled)

Gear, 34-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

Retainer clip, battery (1)/ front clip (1) /rear clip (1)/ foam spacer (1) (for one battery compartment)

Cross pin (4)/ drive pin (4)/ set screw (4) (to rebuild 2 driveshafts)

Suspension down stop screws (includes 2.5mm drill bit) (limits suspension droop, sets maximum ride height)

Gear set, 2-speed wide ratio (2nd speed gear 38T, 13T-18T input gears, hardware)

Antenna crimp nut, aluminum (red-anodized)/ antenna nut tools

Ultra Shocks (grey) (long) (complete with spring pre-load spacers & springs) (2)

Differential output yokes (2)/ 3x5mm countersunk screws (2)/ 3mm set (set) screws (4)

O-ring set: for carb base/ air filter adapter/high-speed needle (2)/ low-speed spray bar (2)

G-spring retainers (wrist pin keepers) (3)

Screws, 3x8mm washerhead self-tapping (6)