traxxas

Primary clutch assembly/ 2x9.8mm pin/ 6x8x0.5 TW (1)

Primary gears: forward (28-T)/ reverse (22-T)/ set screw yoke pin, M3/12 (1)/ 5x10x0.5mm PTFE-coated washer (1)

Propeller

This special shaft allows the use of non-metric 3/16" ID aftermarket props on Traxxas® boats. Two packages are required for dual outdrive boats..

Propeller shaft/ flex cable

Propeller shaft/ flex cable, DCB M41 (380.9mm)

Propeller, 42x59mm

New style plastic propeller for Villain EX. Requires change to smaller pinion gears when used on older Villains equipped with part 1534 and 1533 pr...

New style plastic propeller for Villain EX. Requires change to smaller pinion gears when used on older Villains equipped with part 1534 and 1533 pr...

Push bar, bumper (chrome) (fits #8069 bumper)

Push rod (molded composite) (red) (4)/ hollow balls (8)

Push rod (steel), heavy duty (2) (assembled with rod ends)

Radio tray with RPM mount/ radio tray retainer (2)/ stuffing tube clamp/ 4x16mm BCS (stainless) (2)/ 4x10mm BCS (stainless) (2)

Bumper, Rear/ Bumper Mounts, Rear (upper and Lower) (fits Ford Raptor R)

O-rings (6)

Rebuild kit (heavy duty), slipper clutch (steel disc/ aluminum friction pads (3)/ spring (1)/ 2x9.8mm pin/ 5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))

Rebuild kit, steel constant-velocity driveshaft (includes pins for 2 driveshaft assemblies) (for #9550 front or #9654X rear steel CV driveshafts)

Rebuild kit, center differential (1/16 E-Revo/Slash) (includes o-rings and diff gear covers)

Rebuild kit, fuel tank (includes: mounting post, grommets (2), tank guard, mounting clips (2), cap o-ring, cap o-ring retainer, cap pull ring (2), ...

Rebuild kit, GT-Maxx® shocks (lower cartridge, pistons, piston nuts, bladders, screws) (renews 2 shocks)

Rebuild kit, GTR composite shocks (x-rings, bladders, pistons, e-clips, shock rod ends, hollow balls) (renews 2 shocks)

Rebuild kit, GTR long/xx-long shocks (x-rings, bladders, pistons, piston nuts, shock rod ends, hollow balls) (renews 2 shocks)

Rebuild kit, GTR shock (x-rings, bump stops, bladders, all pistons, piston nuts, shock rod ends) renews 2 shocks

Rebuild kit, GTR shocks (x-rings, bladders, pistons, piston nuts, shock rod ends) (renews 2 shocks)

Rebuild kit, TRX-4® shocks (x-rings, o-rings, pistons, bushings, e clips, rod ends, and travel limiters)

Rebuild kit, oil-filled shocks (o-ring, bladder, piston, shaft guide, E-clips, shock cap, shock rod end) renews 2 shocks

Rebuild kit, slipper clutch (steel disc (2)/ friction insert (2)/ 4.0mm NL (1)/ spring washers (4), metal washer (1))

Rebuild kit, slipper clutch (steel disc/ friction pads (3)/ spring (1)/ 2x9.8mm pin/ 5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))

Rebuild kit, slipper clutch (steel disc/ friction pads (3)/ spring (2)/ pin/ 4.0mm NL (1)/ 5.0mm NL (1))

Rebuild kit, steel constant velocity driveshaft (includes drive pin & cross pin for two driveshaft assemblies)

Rebuild kit, steel constant-velocity driveshaft (includes pins for 2 driveshaft assemblies) (for use only with #7750X driveshaft)

Rebuild kit (for 1/16 E-Revo/Slash steel constant-velocity driveshafts) (includes pins, o-rings, stub axles for driveshafts assemblies)

Rebuild kit, steel-splined constant-velocity driveshafts (includes pins and hardware for one axle shaft)

Rebuild kit, steel-splined constant-velocity driveshafts (includes pins, dustboots, lube, and hardware)

Shock rebuild kit (for 2 shocks)

Receiver Box Cover (for Use Only with #8224 Receiver Box and #2260 BEC)/ Foam Pads/ Seals/ Silicone Grease

Body, Stampede® VXL, orange (painted, decals applied)

Retainer, battery hold-down (front and rear) (1 each)

Reverse installation kit (includes all components to add mechanical reverse (no Optidrive®) to T-Maxx® 3.3) (includes 2060 sub-micro servo)

Ring gear, axle (2)/ pinion gear, axle (2)

Ring gear, differential, 35-tooth (heavy duty) (use with #7790, #7791 11-tooth differential pinion gears)

Ring gear, differential/ pinion gear, differential

Ring gear, differential/ pinion gear, differential