All Products

Half shaft, internal splined (steel-spline constant-velocity) (1)

Body mount (1)/ body mount post (2)/ body post extensions (2) (front or rear)

Half shaft, external splined (steel-spline constant-velocity) (1)

Skid plate, roof (body) (green)/ 3x12 CS (4)

Stub axles, front, heavy duty (2)/ yokes (2)/ pins (4)

Stub axle assembly, rear, outer, extreme heavy duty (1) (left or right) (assembled with internal-splined half shaft)

Cover, gear/ motor wire hold-down clip

Driveshaft, center, 6061-T6 aluminum (blue-anodized)

Gear clutch, complete (high stall)

Driveshaft assembly, front, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

Spur gear, 50-tooth (0.8 metric pitch, compatible with 32-pitch) (for Slash 4x4 center differential)

Driveshaft, center, 6061-T6 aluminum (orange-anodized) (189mm)

Gear, 22-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Body mount (1)/ body mount post (2) (front)

Telemetry trigger magnet holders, spur gear/ magnet, 5x2mm (1)/ 3x8mm CCS (3)/ 3x10mm CCS (3)

Wheelie bar

Gear, 15-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Gear, 12-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Spur gear, 54-tooth, steel (wide-face, 1.0 metric pitch)

Splitter extension (universal)/ 3x10mm CCS (2)

Spur gear, 54-tooth, steel (1.0 metric pitch)

Spur gear, 46-tooth, steel (wide-face, 1.0 metric pitch)

Spur gear, 46-tooth (1.0 metric pitch)

Body support/ 3x12mm CS (4)

Main shaft (2)/ 1.6x5mm BCS (2)

Gear, 14-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw (for use only with steel spur gears)

Distribution block, Pro Scale® Advanced Lighting Control System

Power Module, Pro Scale® Advanced Lighting Control System (includes Mount, Communication Cables, Hardware)

Sensor, temperature and voltage (short)

Stuffing tube (assembled with liner)

Stuffing tube (assembled with liner)

Rudder/ rudder arm/ hinge pin/ 3x15mm BCS (stainless) (2)/ NL 3.0 (2)/4x3mm BCS (stainless, with threadlock) (1)

Telemetry trigger magnet holder, center differential/ magnet, 5x2mm (1)/ 3x8mm BCS (3) (for use with #6814 center differential)

Spring, shock (red) (GTR) (1.8 rate double green stripe) (1 pair)

Propeller shaft/ flex cable

Spring, shock (red) (long) (GTR) (5.4 rate double orange stripe) (1 pair)

Bumper, front/ bumper mount, front/ 4x10mm BCS (2)/ 3x25mm BCS (2)

Steering drag link/ 3x10mm shoulder screws (without threadlock) (2)

Ball bearing, black rubber sealed (20x27x4mm) (2)

Springs, red (for Big Bore shocks) (2.5 rate) (2)

Pull ring (2), fuel tank cap (1)/ engine shut-off clamp (1)