TRAXXAS

LED light harness, rear (requires #5838, 6737X, 6777X, or 6836X rear bumper)

Upper chassis (gray)

This special shaft allows the use of non-metric 3/16" ID aftermarket props on Traxxas® boats. Two packages are required for dual outdrive boats..

Steering Blocks, Left and Right/ Steering Block Arms (aluminum, Dark titanium-Anodized) (2)/ 3x18mm CS (2)/ M3x0.5mm NL (2)

Wire harness (for use with #3475 cooling fan)

Steering blocks, left & right/ steering block arms (aluminum, blue-anodized) (2)/ 3x18mm CS (2)/ M3x0.5mm NL (2)

Bumper, Rear / Bumper Mount (fits 4WD Rustler®) (for LED Light Kit Installation)

Nuts, 3mm nylon locking, flanged, black (8)

Suspension arm covers, green, front (left and right)/ 2.5x8 CCS (12)

Wing/ wing washer (green)/ 4x12mm FCS (2)

Wing/ wing washer (blue)/ 4x12mm FCS (2)

Suspension arm, rear (right), green

Suspension arm, rear (right), black

Body reinforcement set, green/ skid pads (roof) (fits #9511 body)

Wheel hubs, 12mm hex, 6061-T6 aluminum (blue-anodized) (4)/ 3x10 screw pin (4)

Body reinforcement set, blue/ skid pads (roof) (fits #9511 body)

Spur gear, 52-tooth, steel (1.0 metric pitch)

Suspension arm, front (right), blue

Suspension arm, rear (right), blue

Differential, center, complete (fits Sledge®)

Wing mount

Bumper, rear/ skidplate, rear/ tie bar mount, rear/ 3x25 CS (2)

Driveshaft, steel constant-velocity (assembled), front (1)

Servo saver/ servo saver spring/ servo horn, steering (assembled)

Suspension pin set, front & rear (hardened steel), 4x67mm (4), 3.5x48.2mm (2), 3.5x56.7mm (2)/ M3x0.5mm NL, flanged (4)

Stub axle, front

Motor mount, aluminum (upper and lower)/ motor mount spacer/ hardware

Differential output cup, center (hardened steel)/ 2.5x12mm pin

Gear, 13-T pinion (machined, hardened steel) (1.0 metric pitch) (fits 5mm shaft)/ set screw

Camber links, rear (144mm) (2) (assembled with hollow balls)

Carriers, stub axle (left and right)

Camber links, front (117mm) (2) (assembled with hollow balls)

Body mount, rear/ shock guard (body retainer), front

Shock caps, GT-Maxx® shocks (2)/ spring perch/ adjusters (2) (for 2 shocks)

Stub axle, rear (for use only with #9557 rear driveshaft)

Retainer, battery hold-down (front and rear) (1 each)

Servo horn, steering, metal

Gear, 12-T pinion (machined, hardened steel) (1.0 metric pitch) (fits 5mm shaft)/ set screw

Rebuild kit, steel constant-velocity driveshaft (includes pins for 2 driveshaft assemblies) (for #9550 front or #9654X rear steel CV driveshafts)

Steering blocks, left & right/ 4x16mm BCS (4)/ M4x0.7 NL (4)

Wing/ wing washer/ 4x12mm FCS (2)

Tie bars, rear, 6061-T6 aluminum (blue-anodized)

Shocks, GT-Maxx®, aluminum (blue-anodized) (fully assembled w/o springs) (2)